How to Set Up SimRacing Studio with Your Motion Platform
You have unboxed the platform, bolted it together, plugged in the cables, and now you are staring at a software interface with 40 sliders, 6 axis graphs, and no idea where to start. This is the point where most new motion platform owners spend three frustrated evenings before it clicks.
SimRacing Studio (SRS) is the most common motion software for DOF Reality platforms and also supports ProSimu, and a range of other hardware. This guide walks through the complete setup from installation to your first properly tuned session.
Step 1: Install SimRacing Studio
Download SRS from the official SimRacing Studio website. Install it and activate your licence key. DOF Reality platforms include a Pro licence with every purchase. If you bought from SimTorque, your licence key is in your order confirmation email or can be requested from DOF Reality support.
Close any other motion software before installing. SRS needs exclusive access to the USB connection.
Step 2: Hardware Configuration
Open SRS and go to Setup > Hardware. Set the Manufacturer to your platform brand and the Model to your specific unit. For DOF Reality, select your exact model (H2, H3, H4, H6 etc). For ProSimu, select your model and set the COM port for PRS200 actuators.
Once set, the platform should move to its home (centre) position. A yellow indicator in the Hardware Status box confirms the platform is connected and calibrating. A green indicator means it is ready.
Step 3: Axis Assignment
Each actuator needs to be mapped to its physical position on the platform. SRS shows a diagram of actuator positions (Front Left, Front Right, Rear, Traction Loss etc). Match each controller serial number to the correct position.
The serial number is printed on the actuator controller box. If you are unsure which actuator is which, disconnect all but one and move it manually in SRS to identify which physical actuator responds.
Step 4: Game Setup
Go to the Games tab. SRS supports over 100 titles including iRacing, Assetto Corsa Competizione, Assetto Corsa, rFactor 2, Automobilista 2, MSFS, DCS World, X-Plane, Euro Truck Simulator 2, and many more.
Select your game from the list. SRS will show the required plugin or telemetry output method. Some games need a plugin installed in the game folder. Others output telemetry natively via UDP. Follow the per-game instructions in SRS.
Step 5: Motion Profiles
SRS includes community and Pro motion profiles for every supported game. These profiles define how telemetry data translates into actuator movements. Start with the default Pro profile for your game. It provides a balanced baseline that works well for most setups.
Do not start adjusting sliders on day one. Drive with the default profile for at least a few sessions to understand what the platform feels like before changing anything. Most new users over-tune their platform immediately and end up with motion that feels worse than the default.
Step 6: Intellitune (Automatic Tuning)
SRS v2.9+ includes Intellitune, an AI-assisted tuning wizard. It analyses telemetry from a short driving session and suggests optimised settings based on your platform, your game, and community data. Run Intellitune after your first few sessions for a quick improvement over the default profile.
Intellitune runs a 3-minute analysis on a single track. The results are good but not perfect because it only sees one track's telemetry range. For the most accurate tuning, follow the manual tuning process in the SRS documentation after using Intellitune as a starting point.
Step 7: Manual Tuning Basics
Once you are comfortable with the default or Intellitune settings, you can start fine-tuning individual axes.
Pitch (front-back tilt): Controls how much you feel braking and acceleration. If braking feels too aggressive, reduce pitch gain. If you cannot feel acceleration, increase it slightly.
Roll (side-to-side tilt): Controls how much you lean in corners. Too much roll feels like the car is falling over. Too little and corners feel flat. Find the balance where you feel the lean without it being distracting.
Heave (up-down): Controls kerb response and surface changes. High heave settings make kerbs feel violent. Low settings make them subtle. Adjust based on how much surface detail you want to feel.
Traction loss: Controls how much the platform shifts when the rear slides. This is the axis that helps you catch slides before you see them on screen. Start moderate and increase until slides feel informative without being exaggerated.
Common Setup Problems
Platform moves but feels delayed: Check your USB connection. Use a direct USB port, not a hub. Reduce any in-game frame rate limits that might delay telemetry output.
Motion feels too violent: Reduce the Master Gain slider. This scales all axes proportionally. Drop it to 60 to 70% and increase gradually.
One axis does not move: Check the axis assignment in Hardware Setup. The actuator may be mapped to the wrong position. Also check that the specific axis is enabled in the game profile.
Platform does not connect: Ensure no other motion software is running. Check the USB cable and try a different port. Reinstall the USB driver if needed.
Need help with setup? Email us and we can walk you through any configuration issues with platforms purchased from SimTorque.
Frequently Asked Questions
Is SimRacing Studio free?
SRS has a free tier with limited features and a Pro tier with full game support, advanced tuning, and Intellitune. DOF Reality platforms include a Pro licence. ProSimu platforms use SimTools-ProSimu software. SIMRIG and Qubic use their own proprietary control software.
Can I use SimHub instead of SimRacing Studio?
SimHub is primarily a haptic and dashboard tool. It supports some motion hardware but SRS and SimTools are more capable for full platform control. Many users run SimHub for bass shakers alongside SRS for the motion platform.
How long does setup take?
Initial hardware setup and software configuration takes 30 to 60 minutes. Your first tuning session adds another 30 minutes. After that, you launch SRS, select your game, and drive. The software remembers your settings between sessions.